Private well water testing in Texas is the well owner’s responsibility, because private wells are not regulated like public water systems. The basic panel checks for total coliform bacteria, E. coli, nitrate, and salinity (total dissolved solids), and Texas A&M AgriLife advises testing private wells once a year. Test sooner after flooding, pump or well repairs, or any change in taste, color, or smell.
Who is responsible for testing private well water in Texas?
The owner is. The U.S. Environmental Protection Agency does not regulate private wells, and the testing that protects city water does not reach a private well. If your household drinks from a well, the testing schedule is yours to keep.
Livestock water deserves attention too. Salty or stale water suppresses intake, and suppressed water intake costs gains, a point our livestock water guide covers in more detail.
What should you test well water for?
A basic private well panel covers four items, and they are the same four that Texas Well Owner Network screenings check: total coliform bacteria, E. coli, nitrate-nitrogen, and salinity measured as total dissolved solids.
| Test | Benchmark | What a bad result means |
|---|---|---|
| Total coliform bacteria | Should be absent | A pathway exists for surface contamination; check the seal, cap, and recent work |
| E. coli | Should be absent | Waste from people or warm-blooded animals has reached the water; do not drink it untreated |
| Nitrate-nitrogen | 10 mg/L (ppm) drinking water limit | Above 10 ppm is unsafe to drink, especially for infants under six months |
| Total dissolved solids (salinity) | 500 mg/L secondary (taste) guideline | Salty taste, scale, and possible harm to irrigated plants or reduced livestock intake |
How often should you test a private well?
Test once a year as routine, which is what AgriLife Extension advises for Texas private wells. Pick a month you will remember; many owners pair it with the fall well check before winter.
Test again, outside the schedule, when something changes. Floodwater over the wellhead, a new or repaired pump, a broken well cap, a nearby new septic system or feedlot, or a change in taste, odor, or color are all reasons to sample now. After any pump work, we disinfect the system as standard practice, and a follow-up bacteria test confirms it worked.
Where can Panhandle well owners get water tested?
The Texas Well Owner Network, run by Texas A&M AgriLife Extension, holds well water screenings around the state for bacteria, nitrate, and salinity, with a short session explaining results. Watch the network’s site or ask the county Extension office about the next screening near you.
For a certified result, use a laboratory accredited for drinking water analysis and follow its sampling instructions exactly, including the sterile bottle and the hold time. For irrigation or livestock suitability, the Texas A&M Soil, Water and Forage Testing Laboratory offers non-drinking water analysis.
- Get the sterile bottle and instructions from the lab or screening.
- Remove any aerator and run a cold tap for several minutes.
- Fill the bottle without touching the inside of the cap or rim.
- Keep the sample cold and deliver it within the stated hold time.
What do you do if a test comes back bad?
Treat bacteria as a pathway problem first. Coliform in a well usually means surface water is getting in through a cracked cap, a failed sanitary seal, or damaged casing. Disinfecting without fixing the pathway buys a clean test and then a dirty one. A well inspection finds the opening.
High nitrate is a source problem, often from nearby fertilizer, manure, or septic systems, and it is not fixed by boiling, which concentrates nitrate. Use another drinking water source until you have a plan. Very old or failing wells sometimes cannot be sealed economically, and an unused well should be properly plugged or capped so it cannot carry contamination into the aquifer.
Quick Answers
Does Texas require private well owners to test their water?
No state law requires routine testing of a private household well, which is exactly why the owner should schedule it. Lenders and buyers may require a test during a property sale.
Can I boil water to fix a bad test?
Boiling kills bacteria but does not remove nitrate, and it concentrates nitrate as water evaporates. For a nitrate problem, use another drinking source until it is resolved.
How long do results take?
Bacteria tests take a day or two at a lab. Screenings return results with an explanation session. Ask the lab for its turnaround when you pick up the bottle.
Should I test livestock water?
If cattle are drinking less than expected or the water tastes salty, test salinity. It is the most common livestock water quality concern in this region.
Can you test my water?
We are licensed pump installers, so we refer testing to accredited labs and AgriLife screenings. We do inspect the well for the cap, seal, and casing problems that cause bad results.
