Licensed TX Master Water Well Pump Installer · Lic. #61162Call 806-334-0785

Well Owner Guide

How a Windmill Water Pump Works, Part by Part

A windmill water pump converts the wheel’s rotation into an up-and-down stroke, and that stroke drives a pump rod down the well to a cylinder that lifts water with every upstroke. There is no motor and no electricity anywhere in the system. The parts that matter are the wheel, the gearbox, the tail and furl, the tower, the pump rod, the drop pipe, the cylinder, and the leathers, and each one has a predictable way of wearing out.

What are the main parts of a windmill pump?

A windmill pump has an above-ground half that harvests wind and a below-ground half that lifts water. They are joined by the pump rod, which carries the stroke from the gearbox at the top of the tower to the cylinder down in the well.

Windmill pump parts: what each part does and the wear or failure it typically shows in service.
PartWhat it doesTypical wear or failure
Wheel (sails)Catches wind and turns the main shaftBent or missing sails after storms; out-of-balance wobble
Gearbox (mill head)Turns rotation into a vertical stroke, runs in an oil bathWorn gears and bearings when oil is old or low
Tail and furlKeeps the wheel facing the wind; turns it edgewise in high windsWeak furl spring or seized pivot lets storms overspeed the mill
TowerLifts the wheel into clean wind above obstaclesLoose bolts, bent girts, failing anchor posts
Pump rod (sucker rod)Carries the stroke down the wellBroken couplings, worn guides, parted rod
Drop pipeCarries lifted water to the surfaceLeaking joints that drain the column between strokes
CylinderPump chamber downhole with plunger and check valvesWorn barrel or valves; sand scoring
Leathers (cups)Seal the plunger so each upstroke lifts waterThe routine wear item; output falls as they wear

How does a windmill turn wind into pumped water?

The wheel turns the main shaft, and gears inside the mill head drive a crank that moves the pump rod up and down. On the upstroke, the plunger’s leathers seal against the cylinder wall and lift the column of water above them, while the lower check valve opens to let new water into the cylinder. On the downstroke, the lower valve closes and water passes up through the plunger valve, ready for the next lift.

Every stroke delivers a fixed volume, set by the cylinder’s bore and the stroke length. More wind means more strokes per minute and more water, up to the point where the furl turns the wheel out of the wind to protect the mill.

How does cylinder size affect how deep a windmill can pump?

Cylinder size is a trade between volume and depth. A larger cylinder lifts more water per stroke, but every extra inch of bore adds weight to the water column the mill must lift. Deeper wells take smaller cylinders, and the windmill size, stroke, and cylinder are matched together for the lift required.

That is why a mill that pumped well for decades can disappoint after a water level drops. The lift grew, but the cylinder did not change. Resetting the cylinder deeper or changing its size is often part of a rebuild, and our well depth guide explains why levels shift in this region.

What maintenance does a windmill need?

Aermotor’s published schedule calls for a visual check about every six months, an oil change once a year under normal conditions with SAE 10 or lighter non-detergent oil, and a check of nuts and bolts on the mill and tower with the yearly oil change or after a major storm. That schedule is the core of keeping a mill alive.

Leathers are the other routine item. When a mill turns briskly but the trough fills slowly, worn leathers are the first suspect. Pulling the rod and cylinder to replace them is routine work, and it is a good time to inspect the rod couplings and drop pipe joints at the same time.

  1. Every six months: watch the mill run from the ground; listen for knocks and look for wobble.
  2. Every year: change the gearbox oil and check tower and mill bolts.
  3. After major storms: check the furl, sails, and tower before the next high wind.
  4. When output drops: suspect leathers, then leaking drop pipe, then the water level.

What are the warning signs a windmill needs repair?

A clanking or knocking sound at the top of the stroke usually means wear in the gearbox or a loose rod connection. A wheel that wobbles or runs unevenly points to bent sails or bearing wear. A mill that runs but delivers little water points downhole: leathers, a leaking drop pipe, or a falling water level.

The most dangerous sign is a mill that will not furl in high wind. An overspeeding wheel can destroy itself and damage the tower. If the furl does not work, tie the mill off and call before the next front. Our windmill repair and rebuild service covers all of it, from leathers to full tower work.

Windmill or solar: when does a windmill still make sense?

A windmill still makes sense where the site has clean wind, the tower is sound, and the owner values a machine with no electronics. A well-kept mill can serve for decades on cheap parts. For a full side-by-side comparison of output, cost, and weather, read our solar pump versus windmill guide.

Quick Answers

How often should windmill oil be changed?

Aermotor recommends once a year under normal conditions, using SAE 10 or lighter non-detergent oil. A late-fall change prepares the gearbox for cold weather.

How do I know the leathers are worn?

The mill turns normally but delivers noticeably less water than it used to in the same wind. Leathers are the most common cause, followed by leaking drop pipe joints.

Can a windmill pump in winter?

Yes. The cylinder sits downhole below frost, and Panhandle winters bring steady wind. Keep fresh oil in the gearbox and freeze-protect the surface plumbing and tank.

Are windmill parts still available?

Yes. Aermotor still manufactures windmills and parts in San Angelo, Texas, and parts for common mills remain available.

Is it safe to climb a windmill tower?

Tower work is fall-hazard work done with the mill tied off and proper fall protection. We do not recommend owners climb towers; a ground check and a phone call are safer.

Sources

Ask Us About Your Well

Three quick things and someone from the shop will call you back — a real person reads every one of these. Rather just talk?806-334-0785.

How soon?

Free estimates. No spam, no mailing lists — this goes straight to the shop.

Keep your water flowing, no matter where you are.