Licensed TX Master Water Well Pump Installer · Lic. #61162Call 806-334-0785

Well Owner Guide

How to Size a Solar Well Pump

A solar well pump is sized by matching three numbers: the gallons per day the system must deliver, the total dynamic head the pump must lift against, and the sun hours available in the worst month you need water. Those three set the pump model, the panel array, and the storage tank, and getting any one wrong is how solar systems end up short in August or January. This guide walks the same worksheet we fill out before quoting a solar well conversion.

What numbers do you need before sizing a solar pump?

You need five numbers before any pump catalog is useful: daily water demand, the pumping water level in the well, the height from the wellhead to the top of the storage tank, the length and size of pipe to the tank, and the design month. Everything else is derived from those.

Daily demand comes from head count and use, not from the old pump’s size. Our livestock water planning guide carries the gallons-per-head figures we use for hot-weather design. Water level is a measurement, not a memory, which is why we sound the well before quoting. If you only know total depth, you do not yet know enough to size a pump.

Sizing inputs: each input, what it means, and where the number comes from on a typical Panhandle stock well.
InputWhat it isWhere the number comes from
Daily demand (GPD)Gallons the system must deliver per day at peakHead count × gallons per head, plus household or wildlife use
Pumping water levelDepth to water while the pump is runningMeasured with a well sounder during a draw, not the static level
Elevation to tankVertical rise from wellhead to the tank inletSite measurement or a GPS/topo check for distant tanks
Friction lossHead lost pushing water through pipe and fittingsPipe size, length, and flow rate from a friction table
Design monthThe month with the worst sun-to-demand ratioUsually mid-winter for year-round use, peak summer for herd demand

How do you calculate total dynamic head?

Total dynamic head (TDH) is the pumping water level, plus the elevation rise to the tank, plus friction losses in the pipe, plus any pressure required at the outlet. It is expressed in feet, and it is the single number that most decides which pump will work.

Pressure converts to head at about 2.31 feet per PSI. A tank fill that discharges freely needs no added pressure. A system that must push into a pressure tank at 50 PSI adds roughly 115 feet of head, which is why solar systems almost always fill a storage tank and let gravity or a small booster do the rest.

Friction is the input people skip. A long run of undersized pipe can add tens of feet of head and quietly steal output every day. Going up one pipe size often costs less than the extra panels needed to overcome the friction.

  1. Measure the pumping water level (example: 180 ft).
  2. Add the rise from wellhead to tank inlet (example: 15 ft).
  3. Add friction loss from a pipe table at the expected flow (example: 10 ft).
  4. Add outlet pressure converted to feet, if any (example: free discharge, 0 ft).
  5. Total dynamic head = 180 + 15 + 10 + 0 = 205 ft.

How many gallons per minute does the pump need to make?

Required flow is daily demand divided by the effective pumping minutes in your design month. A solar pump does not run all day at full output; it ramps up in the morning and down in the afternoon. Treat the effective window as roughly the peak sun hours for your design month, then confirm against the manufacturer’s output chart for your head.

Worked example: 100 cow-calf pairs at 20 gallons per pair is 2,000 gallons per day. If the design month gives about 6 effective hours, the pump must average about 5.6 gallons per minute at 205 feet of head. That is the point to look up on a pump curve. If the well cannot yield 5.6 GPM, the answer is more storage and a longer pumping day, not a bigger pump. Our well yield guide shows how to find out what the well can actually give.

How big should the solar array be?

The array is sized to the pump’s power draw at your duty point, with margin for heat, dust, and panel aging. Hydraulic power is the floor: water horsepower equals GPM times TDH divided by 3,960. In the example, 5.6 GPM at 205 feet is about 0.29 water horsepower, roughly 215 watts of pure lifting work.

Real systems need several times that at the panels, because motors, pumps, and controllers each lose energy along the way. Solar pump manufacturers publish sizing tools that take GPD, TDH, and location and return the pump and array they have tested together. We use those tools and then check the answer against what we see on similar Panhandle wells, rather than trusting either one alone.

Worked example summary: a 100-pair stock well with a 205-foot total dynamic head needs about 5.6 GPM for six effective hours, about 0.29 water horsepower.
StepValueHow it was found
Daily demand2,000 GPD100 pairs × 20 gal (hot-weather figure)
Total dynamic head205 ft180 ft level + 15 ft rise + 10 ft friction
Effective pumping window~6 hoursDesign-month sun, confirmed on the output chart
Required flow~5.6 GPM2,000 ÷ 360 minutes
Water horsepower~0.29 hp5.6 × 205 ÷ 3,960
Storage4,000–6,000 galTwo to three days of demand

Why does storage matter as much as the pump?

Storage is the battery in a solar water system. Water in a tank is cheaper to buy and longer-lived than electrical batteries, and two to three days of demand in storage carries the herd through cloudy spells without any controller tricks. It also lets you buy a smaller pump that fills slowly all day.

The tank also protects the pump. A float switch or level sensor in the tank tells the controller to stop when full, so the pump is not running against a closed valve. On a stock tank installation we size storage and the float shutoff together for that reason.

What are the common solar sizing mistakes?

The mistakes we fix most often are predictable. Sizing from static water level instead of pumping level leaves the pump short of head every afternoon. Sizing to the annual average sun leaves the system short in the design month. Ignoring friction on a long pipe run steals output silently. And skipping storage forces a pump to chase the herd’s peak thirst in real time.

A less obvious one is buying for today’s water level. Regional levels trend down over decades, so we set the pump with margin below the current pumping level and choose a model with head to spare. When the well needs more than a new pump can fix, pump lowering or deepening is the next conversation.

Quick Answers

Can a solar pump replace my existing electric submersible?

Often, yes. If the well yield and depth fit a solar pump’s range, the existing well can be converted. We check the pumping level and demand first, then tell you whether solar fits or what it would take.

Do solar well pumps need batteries?

Usually not. A storage tank holding two to three days of water does the job of a battery with fewer parts and a longer life. Batteries make sense only where water must be pressurized at night with no tank option.

How deep can a solar pump lift water?

Solar submersibles are built for a wide range of heads, including deep Panhandle wells, but output falls as head rises. The pump curve at your total dynamic head, not the maximum lift on the box, tells you what it will deliver.

Should I size for summer or winter?

Size for the design month: the month where available sun is lowest relative to what you need. For year-round cattle that is often winter; for summer-only grazing it is usually July or August.

What happens on cloudy days?

Output drops in proportion to the light. With two to three days of storage, the herd drinks from the tank while the pump catches up when the sun returns.

Sources

Ask Us About Your Well

Three quick things and someone from the shop will call you back — a real person reads every one of these. Rather just talk?806-334-0785.

How soon?

Free estimates. No spam, no mailing lists — this goes straight to the shop.

Keep your water flowing, no matter where you are.