# How Many Gallons per Minute Does My Well Make?

> How to measure well yield in gallons per minute, what drawdown and recovery tell you, and what GPM a home or herd needs. Panhandle guide. 806-334-0785.

**Source:** https://applewhitewaterwell.com/well-yield-test-gallons-per-minute · Applewhite Water Well Services LLC (Wheeler, TX; TDLR Master Water Well Pump Installer Lic. #61162).
Facts here match the live page. Free to cite with a link to the source URL.

---

Well Owner Guide

By Matthew Applewhite, Texas Master Water Well Pump Installer (TDLR Lic. #61162), Applewhite Water Well. Published November 14, 2026.

Well yield is the rate, in gallons per minute (GPM), that a well can produce steadily without drawing the water level down to the pump. It is different from what the pump can push and different from what comes out of a hose for a few minutes. Yield is measured with a timed flow test while tracking the water level, and it decides what size pump, how much storage, and how much demand a well can support.

## What is the difference between well yield and pump output?

Pump output is what the pump can move. Well yield is what the aquifer can deliver into the well. A large pump on a modest well will out-pump the yield, draw the water down to the intake, and either break suction or run hot, which is one of the [three things that kill well pumps](https://applewhitewaterwell.com/how-long-does-a-well-pump-last) early.

The goal is to match the pump to the yield, then make up the difference between yield and peak demand with storage. That is how low-yield wells water large herds across this region.

## How do you measure a well’s gallons per minute?

A simple flow check starts with a container of known size and a stopwatch. Time how long a 5-gallon bucket takes to fill at a hydrant near the well with the pump running and the pressure tank already drawn down, then divide. A bucket that fills in 60 seconds means 5 GPM at that moment.

That number is pump output under current conditions, not yet yield. To learn yield, the flow test runs long enough for the water level to settle, while someone measures the level with a well sounder. If the level keeps falling at a steady flow, the well cannot sustain that rate.

1.  Measure the static water level with the pump off and the well rested.
2.  Start pumping at a steady, measured flow rate.
3.  Record the water level at set intervals until it stabilizes.
4.  Note the stabilized pumping level; static minus pumping level is drawdown.
5.  Shut off and record how fast the level recovers.

## What do drawdown and recovery tell you?

Drawdown is how far the water level drops while pumping, and recovery is how fast it comes back after the pump stops. Together they describe how freely water moves into the well. A small drawdown at a good flow means a strong well. A large drawdown that never stabilizes means the flow is too high for the well.

Dividing the flow by the drawdown gives specific capacity, in gallons per minute per foot of drawdown. It is a handy way to compare a well to itself over time. If specific capacity falls between service visits, something has changed: the screen may be clogging, or the regional water level may be falling. Both show up in our [well inspection and maintenance](https://applewhitewaterwell.com/well-inspection-maintenance) records.

_Well test terms: static level, pumping level, drawdown, recovery, and specific capacity, with what each tells the owner._

| Term | Definition | What it tells you |
| --- | --- | --- |
| Static water level | Depth to water with the pump off and the well rested | Baseline; compare year to year for regional decline |
| Pumping water level | Depth to water at a steady flow after it stabilizes | Where the pump intake must stay below |
| Drawdown | Static level minus pumping level | How hard the well works at that flow |
| Recovery | How fast the level returns after pumping stops | How quickly the well refills between draws |
| Specific capacity | GPM divided by feet of drawdown | Well health over time; a falling number flags a problem |

## How many gallons per minute does a home or herd need?

Steady GPM converts to daily gallons by multiplying by 1,440, the minutes in a day. A well that sustains 2 GPM can deliver 2,880 gallons in 24 hours if storage is there to catch it. That is why a modest well with a good tank can serve a large operation.

Households feel peak flow more than daily volume: showers, laundry, and outside taps can run at once. A pressure tank and a properly set pressure switch smooth those peaks, and our [low pressure guide](https://applewhitewaterwell.com/well-water-pressure-problems) covers that side. For cattle, the [livestock water planning guide](https://applewhitewaterwell.com/livestock-water-requirements-guide) turns head count into daily demand.

_Steady well yield converted to daily volume: 1 GPM sustained equals 1,440 gallons per day._

| Sustained yield | Gallons per day (24 h) | Roughly supports (with storage) |
| --- | --- | --- |
| 1 GPM | 1,440 | A household, or a small herd |
| 2 GPM | 2,880 | A household plus about 100 pairs at summer demand |
| 3 GPM | 4,320 | A large herd across several troughs |
| 5 GPM | 7,200 | Multiple pastures or a home plus significant stock |

## What can you do if your well yield is too low?

Low yield is usually solved with storage and a slower, longer pumping day before anything more expensive. A smaller pump that runs longer keeps the level above the intake and fills a tank that meets the peak.

If the pumping level is close to the pump, setting the pump deeper buys working room. If the well has silted in or the water level has fallen below the useful section, [pump lowering or well deepening](https://applewhitewaterwell.com/well-deepening-pump-lowering) is the next step, and new drilling is coordinated through licensed drilling partners when nothing else fits. On solar systems, yield sets the ceiling for the whole design, which is why our [solar pump sizing guide](https://applewhitewaterwell.com/solar-well-pump-sizing-guide) starts with it.

From the shop: our opinion

## Why we measure before we sell a pump

We think guessing yield is the most expensive habit in the well business. A pump bought to the wrong number either starves the house or burns itself out, and both cost more than the hour it takes to measure.

So on every pump replacement or conversion, we record the static level, the pumping level, and the flow, and we keep the numbers. Next visit, the comparison tells us whether the well or the equipment has changed.

**Need hands on your well?** These pages cover the work:[Well Inspections & Maintenance](https://applewhitewaterwell.com/well-inspection-maintenance) · [Well Deepening & Pump Lowering](https://applewhitewaterwell.com/well-deepening-pump-lowering) · [Well Pump Repair & Replacement](https://applewhitewaterwell.com/well-pump-repair)

## Quick Answers

Is the GPM on my old well report still accurate?

It was accurate when the well was completed. Water levels and well condition change over decades, so treat the old number as a starting point and re-measure before sizing a new pump.

Can I test well yield myself?

A bucket and stopwatch gives a useful flow snapshot. True yield needs water-level measurements during and after pumping, which takes a sounder and some care. We do both on service visits.

Why does my well do fine in spring and struggle in August?

Summer demand runs the pump longer while regional water levels are often at their lowest. The pumping level sinks toward the intake. A level measurement in late summer shows how much margin is left.

Does a bigger pump get more water out of my well?

Only up to the well’s yield. Past that, a bigger pump just pumps the well down faster. Storage, not horsepower, is how you get more usable water from a modest well.

What is a good specific capacity?

It depends on the formation, so the most useful comparison is your well against its own past numbers. A steady figure is good news; a falling one means it is time to look closer.

## Sources

-   [Wellowner.org — National Ground Water Association](https://wellowner.org)
-   [Texas Water Development Board — Groundwater Data](https://www.twdb.texas.gov/groundwater/data/index.asp)

## Ask Us About Your Well

Three quick things and someone from the shop will call you back — a real person reads every one of these. Rather just talk?[806-334-0785](tel:+18063340785).

## Keep your water flowing, no matter where you are.

[Call 806-334-0785](tel:+18063340785)[Get a Free Estimate](https://applewhitewaterwell.com/contact-us)
